Consider the circuit shown. Assume that the diode  is ideal. The supply voltage , and . The peak diode current (in amperes) is

(Round off to one decimal place)

Consider the circuit shown. Assume that the diode () is ideal.

Given , and  , the average value of the current through the diode is  A

(Round off to two decimal places)

The input voltage  and current  of a converter are given by,

where, . The input power factor of the converter is closest to

 feeds an ideal inductor  through an ideal SCR with firing angle . If , then the peak of the inductor current, in ampere, is closest to

In the following circuit, the average voltage

where  is the firing angle. If the power dissipated in the resistor is 64 W, then the closest value of  in degrees is

A single-phase half-controlled bridge converter supplies an inductive load with ripple free load current. The triggering angle of the converter is . The ratio of the rms value of the fundamental component of the input current to the rms value of the total input current of the bridge is ________ (rounded off to 3 decimal places).

A single-phase full-controlled thyristor converter bridge is used for regenerative braking of a separately excited DC motor with the following specifications:

Assume that the motor is running at 600rpm and the armature terminals of the motor are suitably reversed for regenerative braking. If the armature current of the motor is to be maintained at the rated value, the triggering angle of the converter bridge in degrees should be ________ (rounded off to 2 decimal places).

The single phase rectifier consisting of three thyristors  and a diode  feed power to a  constant current load.  and  are fired at α=60°  and  is fired at α=240° . The reference for  is the positive zero crossing of . The average voltage  across the load in volts is ________ (Round off to 2 decimal places).

A single-phase full-bridge diode rectifier feeds a resistive load of 50 Ω from a 200 V, 50 Hz single phase AC supply. If the diodes are ideal, then the active power, in watts, drawn by the load is _____________. (round off to nearest integer).

The voltage at the input of an AC-DC rectifier is given by where ω = 2π × 50 rad/s. The input current drawn by the rectifier is given by .

The input power factor, (rounded off to two decimal places), is, _________________ lag.

For the ideal AC-DC rectifier circuit shown in the figure below, the load current magnitude is  and is ripple free. The thyristors are fired with a delay angle of 45°. The amplitude of the fundamental component of the source current, in amperes, is __________. (round off to two decimal places)

A single-phase, full-bridge diode rectifier fed from a 230 V, 50 Hz sinusoidal source supplies a series combination of finite resistance. R, and a very large inductance, L. The two most dominant frequency components in the source current are:

A single-phase fully-controlled thyristor converter is used to obtain an average voltage of 180 V with 10 A constant current to feed a DC load. It is fed from single-phase AC supply of 230 V, 50 Hz. Neglect the source impedance. The power factor (round off to two decimal places) of AC mains is ________.

The waveform of the current drawn by a semi-converter from a sinusoidal AC voltage I source is shown in the figure. If , the RMS value of fundamental component of the current is _______ A (up to 2 decimal places).

A single phase fully controlled rectifier is supplying a load with an anti-parallel diode as shown in the figure. All switches and diodes are ideal. Which one of the following is true for instantaneous load voltage and current?  

A phase controlled signal phase reflector, supplied by an AC source, feeds power to an R-L-E load as shown in the figure. The reflector output voltage has an average value given by , where and is the firing angle. If the power delivered to the loss less battery is 1600W, in degree is ______ (up to 2 decimal places)

The figure below shows an uncontrolled diode bridge rectifier supplied from a 220 V, 50 Hz, 1-phase ac source. The load draws a constant current . The conduction angle of the diode  in degrees (rounded off to two decimal places) is ____________.

In the circuit shown, the diodes are ideal, the inductance is small, and . Which one of the following statements is true?

The figure below shows the circuit diagram of a controlled rectifier supplied from a 230 V, 50 Hz, 1-phase voltage source and a 10:1 ideal transformer. Assume that all devices are ideal. The firing angles of the thyristors  and  are 90° and 270°, respectively.

The RMS value of the current though diode  in amperes is ___________.

A phase-controlled, single-phase, full-bridge converter is supplying a highly inductive DC load. The converter is fed from a 230 V, 50 Hz, AC source. The fundamental frequency in Hz of the voltage ripple on the DC side is

In the circuit shown in the figure, the diode used is ideal. The input power factor is ___________ . (Give the answer up to two decimal places)

A single-phase thyristor-bridge rectifier is fed from a 230V, 50Hz, single-phase AC mains. If it is delivering a constant DC current of 10A, at firing angle of , then value of the power factor at AC mains is

A full-bridge converter supplying an RLE load is shown in figure. The firing angle of the bridge converter is  . The supply voltage . . The inductor L is large enough to make the output current  a smooth dc current. Switches are lossless. The real power fed back to the source, in kW, is____________.

A single-phase bi-directional voltage source converter (VSC) is shown in the figure below. All devices are ideal. It is used to charge a battery at 400V with power of 5kW from a source  V (rms), 50Hz sinusoidal AC mains at unity p.f. If its AC side interfacing inductor is 5mH and the switches are operated at 20kHz, then the phase shift  between AC mains voltage  and fundamental AC rms VSC voltage , in degrees, is_____.

In the given rectifier, the delay angle of the thyristor  measured from the positive going zero crossing of  is . If the input voltage is  V, the average voltage across R (in Volt) under steady-state is __________.

The figure shows the circuit of a rectifier fed from a 230 – V (rms), 50 – Hz sinusoidal voltage source. If we want to replace the current source with a resistor so that the rms value of the current supplied by the voltage source remains unchanged, the value of the resistance (in ohms) is _________ (Assume diodes to be ideal)         

The figure shows the circuit diagram of the rectifier. The load consists of a reactance  and an inductance 0.05H connected in series. Assuming ideal thyristor and ideal diode, the thyristor firing angle (in degree) needed to obtain an average load voltage of 70V is_____________

A fully controlled converter bridge feeds a highly inductive load with ripple free load current. The input supply  to the bridge is a sinusoidal source. Triggering angle of the bridge converter is . The input power factor of the bridge is _____________.

A diode circuit feeds an ideal inductor as shows in the figure, Given ,  where , and L = 31.83 mH. The initial value of inductor current is zero. Switch S is closed at t = 2.5ms. The peak value of inductor current  (in (a) in the first cycle is ____________.

Thyristor T in the figure below is initially off and is triggered with a single pulse of width 10μs. It is given that and. Assuming latching and holding currents of the thyristor are both zero and the initial charge on C is zero, T conducts for

A half-controlled single-phase bridge rectifier is supplying an R-L load. It is operated at a firing angle  and the load current is continuous. The fraction of cycle that the freewheeling diode conducts is

The input voltage given to a converter is

The current drawn by the converter is

The input power factor of the converter is

The input voltage given to a converter is

The current drawn by the converter is

The active power drawn by the converter is

The fully controlled thyristor converter in the figure is fed from a single-phase source. When the firing angle is, the dc output voltage of the converter is 300V. What will be the output voltage for a firing angle of , assuming continuous conduction?

The circuit shows an ideal diode connected to a pure inductor and is connected to a purely sinusoidal 50Hz voltage source. Under Ideal conditions the current waveform through the inductor will look like

A single phase fully controlled bridge converter supplies a load drawing constant and ripple free load current. If the triggering angle is 30°, the input power factor will be

A single-phase half controlled converter shown in the figure is feeding power to highly inductive load. The converter is operating at a firing angle of 60°.

If the firing pulses are suddenly removed, the steady state voltage waveform of the converter will become

A single phase fully controlled converter bridge is used for electrical braking of a separately excited dc motor. The dc motor load is represented by an equivalent circuit as shown in the figure. Assume that the load inductance is sufficient to ensure continuous and ripple free load current. The firing angle of the bridge for a load current  will be

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25° and an overlap angle of 10° with constant dc output current of 20 A. The fundamental power factor (displacement factor) al input ac mains is

A single phase full-wave half-controlled bridge convener feeds an inductive load. The two SCRs in the converter are connected to a common DC bus. The converter has to have a freewheeling diode

A single-phase, 230V, 50 Hz ac mains fed step down transformer (4:1) is supplying power to a half-wave uncontrolled ac-dc converter used for charging a battery (12 V dc) with the series current limiting resistor being 19.04 Ω. The charging current is

In the circuit of adjacent figure the diode connects the ac source to a pure inductance L.

The diode conducts for

A single-phase half wave uncontrolled converter circuit is shown in figure. A 2-winding transformer is used at the input for isolation. Assuming the load current to be constant and, the current waveform through diode will be

A single-phase bridge converter is used to charge a battery of 200V having an internal resistance of 2Ω as shown in figure. The SCR’s are triggered by a constant dc signal. If SCR 2 gets open circuited, then what will be average charging current?

A single-phase half wave controlled rectifier is driving a separately excited dc motor.  The dc motor has a back emf constant of 0.5 V/rpm. The armature current is 5A without any ripple. The armature resistance is 2Ω.

The converter is working from a 230 V, single-phase ac source with a firing angle of 30°. Under this operating condition, the speed of the motor will be

A phase controlled half controlled single phase converter is

shown in Figure. The control angle

α = 30°. The output dc voltage wave shape will be a s shown in        

In the single phase diode bridge rectifier shown in figure, the load resistor is R = 50Ω.

The source voltage is v=200sin(ωt), where ω=2π × 50 radians per second. The power dissipated in the load resistor R is

A half-wave thyristor converter supplies a purely inductive load, as shown in Figure. If the triggering angle of the thyristor is 120°, the extinction angle will be  

A single-phase full bridge voltage source inverter feeds a purely inductive load, as shown in figure, where , , ,  are power transistors and , , ,  are feedback diodes.  The inverter is operated in square-wave mode with a frequency of 50 Hz.  If the average load current is zero, what is the time duration of conduction of each feedback diode in a cycle?

Resonant converters are basically used to

When the firing angle α of a single phase, fully controlled rectifier feeding constant d.c. current into a load is 30°, the displacement power factor of the rectifier is:

An SCR is connected in series with a 300V ac supply and a 300 ohms load resistor. Calculate for a firing angle of 45°

1. The reading of a moving coil ammeter connected in series with the load and
2. The reading on a moving iron voltmeter connected across the SCR

A single phase diode bridge rectifier supplies a highly inductive load. The load current can be assumed to be ripple free. The ac supply side current waveform will be:

The single phase half controlled ac to dc bridge converter of figure supplies a 10 Ohm resistor in series with a 100V back emf load. The firing angle of the thyristors is set to 60°

(i) Find the average current through the resistor

(ii) What will be the new average current through the resistor, if a very large inductor is connected in series with the load?

Referring to the figure the type of load is

A line-commutated inverter changes dc voltage to ac voltage. (True=1/False=0)